Skip to main content

Filter By:

  • Show More Brands

  • Show Fewer Brands
  • Show More Sizes
  • Show Fewer Sizes
  • Show More Model Years
  • Show Fewer Model Years

Other

$113.00
7.5mm, 10mm, 25-35mm (used for Reverb service) - Reverb AXS/Reverb A1-B1/Reverb Stealth A2-C1
$110.00
- Accessory base plate to mount EnergyPak Plus on the bike. - EnergyPak Plus accessory comes with a water bottle cage adaptor plate that can be mounted to the base plate when the EnergyPak Plus is not in use.
$106.00
All CeramicSpeed Bearings are hand-built in Denmark. Super-smooth CeramicSpeed grade 3 Silicone Nitride balls are matched (within microns) with hardened steel raceways that feature an ultra-smooth polished groove. The balls are held in place by a reinforced polyamide cage. Every bearing is optimized with a low-viscosity CeramicSpeed All Round Grease to minimize friction and increase bearing life. Non-contact seals complete the bearings, keeping dirt and moisture out. CeramicSpeed Bearings can be used for any cycling discipline: Road, TT, Tri, Track, Cross, and MTB. The benefits are super low friction, better power transfer, and increased bearing life. During the building process, we check each bearing four times by hand to ensure that all parts are matched perfectly. CeramicSpeed Balls are 400% smoother, 128% harder, and 58% lighter than standard steel bearings normally used in the bicycle industry. When comparing the CeramicSpeed Balls with other ceramic balls in the industry, you will find that the CeramicSpeed Balls are 15% harder, take 99% higher loads, and are 100% smoother. - Inner Diameter: 12mm - Outer Diameter: 24mm - Width: 6mm
$105.99
Cane Creek Progressive Rate VALT coil springs are designed to provide riders with a true rise-in-rate spring curve. - Springs feature the progressiveness and ramp-up that hard-charging riders demand - Designed for use with Cane Creek Coil shocks - Progression begins at 50% into the stroke of the spring - Crafted from high-performance spring steel - Inner diameter of 36.5mm is compatible with all Cane Creek coil shocks
$105.00
-Seatpost clamp for Propel Advanced ISP models (2013-2016)
$104.00
The new DebonAir+ is built to strike the perfect balance of what riders really want: butter-like small bump feel, increased air volume to add support throughout the travel and higher overall ride height for more confidence when things get steep.
$104.00
The new DebonAir+ is built to strike the perfect balance of what riders really want: butter-like small bump feel, increased air volume to add support throughout the travel and higher overall ride height for more confidence when things get steep.
$103.95
Metric fastener kit with an assortment of nuts, bots and washers. - Assortment of commonly used bicycle fasteners
$102.95
Inspired by those long rides when daylight turns to darkness and back to sunlight, the new Ritchey Mini Sliver clip-on bar offers welcome comfort and a more efficient position. These clip-on bar extensions and pads were designed specifically for off- and on-road ultra-endurance racing and riding. The Mini Sliver features a smaller version of our original padded Sliver clip-on armrests, allowing for less interference with handlebar bags and other accessories. The adjustable alloy bar extensions deliver a comfortable and aero position for successful long-distance gravel racing and pleasant extended bike touring. - Includes two sets of armrest pads - Reversible extensions: 70 or 90mm - Built specifically for ultra-distance riding - Material: aluminum 6061 - Handlebar clamp diameter: 31.8mm - Handlebar clamp width: 16mm - Stack height: 31mm - Reversible and replaceable extensions - Replaceable stick-on pads - Weight: 286g
$100.00
Salsa Pivot Service Kits
$100.00
Salsa Split Pivot Suspension Service Kits, for all 2014+ Horsethief, Pony Rustler, Spearfish, Redpoint and Deadwood Sus frames.
$100.00
Mate Specialized's Clip-On Clamp to a pair of aero extension bars and get time on your side. Their 22.2mm diameter is compatible with many standard aftermarket extensions, and with a one-bolt hinge system, they're simple to install.
$99.99
Ergonomic Legacy II Aerobars feature extensions that provide a variety of hand positioning, and width and rotational armrests with a high stack to achieve a relaxed ride position. Ideal for riders that need extra positions for Centuries. - Injected Venturi Armrest and ZB Bracket - Forged 6061-T6 construction with armrest made of injected nylon and glass fiber - Fixed extension adjustment - Extension angle 44 degrees with 58mm rise - Fits both 26.0 and 31.8mm basebars, shims included
$99.00
RockShox Sektor DebonAir Assemblies - Includes air top cap, Air spring and shaft bolt
$95.00
ELEVENSIX coils are precision manufactured at HyperCo's state-of-the-art USA facility and available in 25lb/in increments for uncompromising setup. Each HyperCoil suspension spring is individually inspected, and laser marked with size and rate information for the ultimate in accuracy!
$36.95 - $95.00 $95.00 Up to 61% Off
The new generation spring series features a race-ready weight with big mountain strength. You'll also find advanced technologies that feature a multi-step surface treatment process, as well as cutting-edge heat treatments. Lastly, we use wire materials that allow us to stress the wire harder, without causing damage to the spring, and therefore design lighter springs. - Precise spring rates are broken down to 4 N/mm (23 lbs./in).
$36.95 - $95.00 $95.00 Up to 61% Off
The new generation spring series features a race-ready weight with big mountain strength. You'll also find advanced technologies that feature a multi-step surface treatment process, as well as cutting-edge heat treatments. Lastly, we use wire materials that allow us to stress the wire harder, without causing damage to the spring, and therefore design lighter springs. - Precise spring rates are broken down to 4 N/mm (23 lbs./in).
$34.95 - $95.00 $95.00 Up to 63% Off
The Ohlins RXF 36 Coil Fork Spring sets a new benchmark for spring rate accuracy and light weight for trail and all-mountain fork springs. - Ultra-fine spring rates to ensure perfect set up for all weights. - Spring rates are broken down to 0.9 N/mm (5 lbs./in). - Fits Ohlins RXF Coil fork only.
$94.99
Eliminate dropped chains forever with the new OneUp Components Bash Guide. As the trend for lower and slacker bikes continues, chainring protection is becoming even more important. Revised for 2019 the OneUp Bash Guide uses simple, one tool installation and adjustment as well as an all new tool less flip The OneUp Bash Guide was developed with input from top EWS World racers and can be seen all over this years circuit. Reinforced Nylon bash guards and a back plate cut from 8mm thick 7075-T6 aluminum, ensure that the OneUp Bash Guide can handle the biggest hits, but at a weight of only 105g (34T) you may forget it’s even there. NOT JUST FOR ENDURO RACERS. The OneUp Bash Guide is equally at home on your trail bike, where the extra bash protection is a must for aggressive riders or on your DH rig. With the popularity of clutch derailleurs, it is no longer necessary to run a chain guide with a lower roller to effectively tension your chain. DH racers and Bike Park rippers will appreciate the huge reduction in drag with the elimination of the lower roller, without sacrificing any strength or chain retention. The OneUp Bash Guide includes 3 different sizes of bash plate for compatibility with chainrings from 28-36T. FEATURES - Tool less upper guide flip - Install without removing your crank - Single tool install and adjustment - Boost compatible - Oval Compatible - Black Stainless Steel hardware - Includes 3 bash plates (28-30T, 32-34T, 36T) - Patented US 10,053,188 Other Patents Pending SPECS - Weight: 90g 28-30T, 105g 32-34T, 110g 36T - Capacity: 28-36T - Chainline: 7.5mm adjustment - Mount: ISCG05 - Color: Black top guide piece included - Material: 7075 aluminum, top guide glass reinforced thermoplastic
$91.00
The forged aluminum bracket offers solid, easy-to-use construction alongside an industry-leading fit range. It is also compatible with our riser kits. The bracket is designed for 31.8mm bars and 22.2mm extensions in aluminum or carbon. - Materials: Forged 6061-T6 AL - Stack Height: 42.6mm - Width Adjustment: 37mm - Basebar Clamp Diameter: 31.8mm - Extension Clamp Diameter: 22.2mm - Weight: 234g
$89.99
e*thirteen Press Fit Bottom Brackets - Adapts all e-thirteen and older Fifteen.G cranks to BB89.5 BB92 frames - Custom angular contact bearings TiNi models feature Ti Nitride races - EV-8015 includes chainline spacer kit for LG1 and non-APS cranks - e*thirteen's BB92 bottom bracket uses industry-exclusive dual-row bearings to fit big performance into a small BB shell - A center tube helps seal the BB shell - For 41mm ID pressfit frames - Bearings feature high-performance seals, and a custom grease specification delivers supreme durability and smooth spinning performance
$84.99
36 Air Shaft Assembly for Fox suspension forks.
$84.99
The OneLoc remote provides total control over your suspension at your fingertips. The increased leverage at the bar, translate in a smoother and easier actuation. - Can be mounted above or below handlebars - Great match for SRAM 1x drivetrains - Tall clamp allows OneLoc to easily fit non-SRAM components
$84.95
ReMote Sustain Lever - Levers are Reverb Stealth series specific - A-series have no Rockshox marking below the head whereas B-series have gold Rockshox markings below the head - Engineered break-away pivot that allows the lever to break away from the pivot in the event of a crash - Cable Kind Clamp does not damage secured cables and features captive hardware - Only compatible with Reverb Stealths - Features a leak-proof, robust, and low-maintenance mechanical actuation system - Easy cable detachment for service, travel or bike shipping - 40mm reduction in in-frame height compared to Connectamajig Reverbs
$84.95
ReMote Sustain Lever - Levers are Reverb Stealth series specific - A-series have no Rockshox marking below the head whereas B-series have gold Rockshox markings below the head - Engineered break-away pivot that allows the lever to break away from the pivot in the event of a crash - Cable Kind Clamp does not damage secured cables and features captive hardware - Only compatible with Reverb Stealths - Features a leak-proof, robust, and low-maintenance mechanical actuation system - Easy cable detachment for service, travel or bike shipping - 40mm reduction in in-frame height compared to Connectamajig Reverbs
$84.95
ReMote Sustain Lever - Levers are Reverb Stealth series specific - A-series have no Rockshox marking below the head whereas B-series have gold Rockshox markings below the head - Engineered break-away pivot that allows the lever to break away from the pivot in the event of a crash - Cable Kind Clamp does not damage secured cables and features captive hardware - Only compatible with Reverb Stealths - Features a leak-proof, robust, and low-maintenance mechanical actuation system - Easy cable detachment for service, travel or bike shipping - 40mm reduction in in-frame height compared to Connectamajig Reverbs
$82.00
Fit Kit SET815 contains all the parts needed to thru axle mount an Old Man Mountain bike rack to the rear of your bike with a 12mm rear thru axle. This kit includes: - 12 x 217—229mm thru axle with 1.0 mm thread pitch - A pair of pucks - Clear protective tape - Stainless steel mounting hardware - Axle mounting increases our rack's load capacity to 70lbs/33kg - Fit Kits make it easy to swap between bikes or front and rear mounting with just a few bolts - Fit Kits protect your bike. Not all bike eyelets are meant for racks, most are only made for fenders or have very low weight limits. Axle mounting protects your frame We partner with The Robert Axle Project to supply our thru axles. Axle Length does NOT equal hub standard. This refers to the length of the axle shaft. All axles are compatible with +/- 2mm.