Parts & Accessories

Spacers to insure proper chainline and chainring spacing on your bike. • 0.6mm thick • Sold in a bag of 20 spacers

• ISIS interface • Only includes left crank • 175mm length

• Forged steel • 6 1/2-inch • Compatible with 9/16" pedals • Left crank • Cotterless

Wheels Manufacturing BB30 Bottom Bracket Adaptor for GXP Cranks adapts 22/24mm Spindle Cranks (SRAM/TruVativ) to work on BB30 frames. Simply tap the adapters into the 6806 bearing in the BB shell, then install the spindle and cranks. Use Wheels Mfg Crank Spindle Spacers to adjust your chainline, or take up any side-to-side movement in your cranks. These spacers are machined from engineering-grade Delrin.

The Wheels Manufacturing BBright Press Fit Bottom Bracket Adaptor for GXP Cranks adapts 24/22mm cranks (SRAM, Truvativ, etc.) to most BBRight frames. Compatible with 2011-2012 Cervelo models R3, R3 Team, S5, S5 Team, S5 VWD, R5ca and R5 VWD. - Includes eight 0.7mm shims for fine-tuning chain line - Machined engineering-grade Delrin - 8g/pr

absoluteBLACK Chainring Bolts are used to mount chainrings to the crank arms. Bolts are crafted from 7075 T6 aluminum and hard anodized for durability. - Bolts use a Torx T30 interface for greater reliability - Short bolts are used for the following chainrings: 104 BCD oval 34/36t, 104 BCD round 32/34/36/38t, and bashrings - Set of 5

- Enables the use of various cranks with BB386EVO PF30 or BB30 bottom brackets - Spacers and adapters only specific bottom brackets are required and sold separately

Fits 19mm team & talon cranks: - Splines: 48 - Diameter 19mm - Length: 5.5" (140mm) - Spindle bolts: 3/8" X24tpi (not included) - Also fits: Cult OS, Demolition Revolt, Rant 48-S, WTP Royal, Redline Device and other 19mm 48 spline cranks

- Material: Heat-treated 4130 Chromoly - Splines: 8 - Diameter: 19mm - Length: 5.7/8" (150mm) - Spindle Bolts: 8x1mm (Included) - Compatibility: Fits Stolen OEM/MOB/SIC Mission Transit, Rant 8-S, Sunday Saker and most other 19mm, 8 spline cranks

The Wolf Tooth CAMO BashSpider is a crankset-mounted boost bash ring. This is a spider with an integrated bash ring for use with direct mount cranksets. The CAMO BashSpider pairs with a CAMO chainring to complete the CAMO System. - A CAMO chainring is required to complete this system - The "rolling" ability of the BashSpider allows the rider to move easily over obstacles - Bash rings that are mounted on the crankset are better supported than bash rings that are mounted to the frame or bottom bracket - M5 (minus 5mm - Boost) is dished towards the frame for 52mm chainline for bikes with Boost spacing - Will fit CAMO chainrings from sizes 28T-34T round or 30T-32T elliptical - Includes mounting bolts - Designed to work with Shimano cranksets that have a removable spider

RaceFace CINCH Spindle - Fits 150/157mm Hub Spacing

TruVativ's Stylo All Mountain Guard is all-mountain chainring protection with style. This 4mm thick aluminum guide is 4 bolt, 104 BCD compatible.

Race Face Crank Arm Tab Spacers • Spacers are used to protect the outer chainring tabs and enhance aesthetic when no outer ring or bashguard is used • Fits all Race Face cranksets • Use double bolts

Wolf Tooth's CAMO stands for Chainline and Material Optimization. Available in various chainlines and spider configurations, CAMO spiders allow the use of previously unavailable chainring styles, materials, and chainlines in a lightweight, modular, and customizable package. These spiders are for use with the SRAM cranksets that have removable Direct Mount spiders and are only compatible with CAMO rings and bolts. Four different chainline options are available. The number and letter refer to the mm offset and direction from the mounting face to the centerline of the teeth: - M8 (minus 8mm - dished toward the frame): For 49mm chainline, used with GXP and long-spindle BB30 cranks. Designed for bikes with 135mm QR, 142mm thru axle, and some 148mm bikes. - M5 (minus 5mm - dished toward the frame): For 52mm chainline (Boost) - M2 (minus 2mm - dished toward the frame): For 49mm chainline on short-spindle BB30 cranks - P2 (plus 2mm - dished outward away from the frame): For fat bikes that have 190/197 rear spacing but use a 100mm-spindle crank. Can also be used to achieve a Boost chainline with a short-spindle BB30 crank.

RaceFace CINCH Spindle - Fits 135/142 and 141/148mm Hub Spacing

RaceFace Crank Arm Fixing Bolts - M15

- Chainring bolt sets are available in sets of four or five - Bolts have 5mm hex heads - Inner Length: M8x7.5mm Bolt (x4) / M8x7mm Nut (x4) - Material: Steel - Type: 1x

For Race Face 30mm Cinch System cranks only. Use RF-2999 for 8mm to 16mm hex wrench adapter to remove spindle. - 30 x 136.5mm is for 120mm spaced BMX hubs and 68/73mm BBs - 30 x 151.5mm is for 150/157mm Hubs

Easton spider and ring assemblies for CINCH cranks.

• Adjustable aluminum chain guard • Fits front chainrings from 38T to 48T • Multiple clamp options fit seat tubes from 25.4 to 34.9mm • Black anodized finish

SRAM Force crank spiders are for repairing your crank or converting it to different gearing. Available in 110mm and 130mm BCDs.

Power every ride. We've taken the reliability, elegance, and features of Quarq's legendary crank-based power meter and dropped the barrier to entry once again. This new power meter platform is entirely contained within the DUB spindle for clean integration that fits more bikes than ever. It's invisible technology that adds minimal weight and will help you get to the finish line faster, and it can be used to upgrade any eTap AXS bike. - An elegant, integrated design - DUB-PWR spindle-based unit measures left-side power to calculate total watts - Proven Quarq reliability and accuracy - Long battery life (400+ hours) to power a season of rides - User-replaceable lithium AAA battery - DUB bottom bracket adds durability and simplicity - Waterproof (IPX7 waterproof to 1 meter for 30 minutes) - Lightweight (less than 40g heavier than standard crankset) - Simple and affordable power meter upgrade option - Right Arm/BB/Spider/Chainrings NOT INCLUDED

The Easton Spider and Ring assembly features the Cinch Direct Mount System, making a swap between ring configurations a fast and simple procedure. This system also provides a significant weight savings by eliminating the material overlap and extra bolt hardware that is required for a traditional spider with chainring configuration. - EA90 Aluminum

- Horizontal square interface - Only includes left crank

- Replacement bolt for DUB cranks

- Crank dust cap - Works with most three-piece crank models

- Crank Arm Length: 175mm - Interface: ISIS - Position: Left

Race Face Crank Arm Fixing Bolts - M18 Crank Bolt - Fits 15SX/Atlas/SixC CINCH - Not self-extracting

Replacement crank arm for X5 GXP

The Wolf Tooth CAMO BashSpider is a crankset-mounted boost bash ring. This is a spider with an integrated bash ring for use with direct mount cranksets. The CAMO BashSpider pairs with a CAMO chainring to complete the CAMO System. - A CAMO chainring is required to complete this system - The "rolling" ability of the BashSpider allows the rider to move easily over obstacles - Bash rings that are mounted on the crankset are better supported than bash rings that are mounted to the frame or bottom bracket - M5 (minus 5mm - Boost) is dished towards the frame for 52mm chainline for bikes with Boost spacing - Will fit CAMO chainrings from sizes 28T-34T round or 30T-32T elliptical - Includes mounting bolts - Designed to work with the Race Face Cinch cranksets that have a removable spider

Used to adjust crank chainline or take up any slack when using 29mm (SRAM DUB) spindle cranks. - 29mm I.D. - 2.5mm thick - 5 spacers per bag - Machined engineering-grade Delrin

Calibur V2 Spindle replacement parts

RaceFace CINCH Crank Bolt and Puller Cap Sets.

- Octalink bolts include steel washers, JIS includes black plastic caps - HT2 mount bolts (low torque plastic, except XTR-M970 aluminum) are for mounting non-drive arm - Hollow bolts (SH-21504) not recommended for non-treated spindles

- Series: SLX - Crank Construction: HOLLOWTECH II Technology

- Crank Construction : HOLLOWTECH II - Optimum power transfer

TruVativ Crank Arm Fixing Bolts - Monocoque carbon crankset with hollow-arm design - FSA Mega Tooth chainring design greatly improves chain retention - FSA BB392 compatibility allows use in nearly any frame - Bottom bracket not included

Replacement crank bolt/puller set for Race Face NEXT XC, SIXC, and 2088 and newer Deus cranks.

Machined engineering-grade Delrin inserts for adapting bottom brackets to a different type of crankset spindle. - Adapts PF30 and Cannondale BB30-73A bottom brackets for use with Hollowtech II cranksets - Delrin adaptors fit between bearings and crank spindle - BB Shell Width (mm): 68 mm , 73 mm - Spindle Interface Type: Hollowtech II - BB/Frame Interface: PF30

- 7075-T6 aluminum direct mount spider or lockring to fit Race Face Cinch system splined cranks - RF-3296 spider is required for running 2-ring setups with Boost (Race Face 1x Direct Mount rings work fine with Boost) - Mounts using a common Park BBT-22 tool

The absoluteBLACK premium crank bolt and bolt cover sets are designed to cover the small step down between chainring and crank arms. - Designed to fit Shimano Ultegra 6800 cranks - Includes 4 T30 Torx bolts and 4 bolt covers - Not compatible with absoluteBLACK Sub Compact oval chainrings

These spiders are optimized to fit Cane Creek's eeWings All-Road cranks, adding more versatility for riders. The spiders will allow direct-mount cranks, such as the eeWings, to accommodate 110 BCD chainring so riders can expand their gearing options. - Allows riders to run more 1x chainring options - CNC high grade 7075 series aluminum with black anodized finish - 50g

Utilizing MRP's patented integrated skid (US Patents RE 42,436 / 8,235,849 Patents Pending), the XCg tucks neatly behind your crankset and protects those costly chainrings from damage. The replaceable nylon skid glides over rocks and obstacles. - Great accessory to protect costly chainrings - Integrated skid protects chainrings and glides over rocks and obstacles - 88g (XCg V2 32t, ISCG-05 model)

Revamp the look of your single speed cranks with some new hardware. Origin-8's Single Chainring Bolts give a high polished look to any crankset. The anodized finish comes in multiple colors to highlight your crank and makes it look as good as you do. You can also choose between steel or aluminum bolts. • Set of 5 male/female bolts • Inside measures 4mm when tightened, 7mm total height

Forged AL6061-T6 alloy spiders for Origin8 Thruster Series modular cranksets - SRAM 3-bolt interface for crank arm mounting - Available in both single and double chainring configurations for MTB, Boost/Fat, and Road/Cross/Gravel applications - BCD: 104mm 4-Bolt - Type: 1x

Race Face CINCH Spindle

Replacement crank arm for XX1 Eagle GXP

This very light, stiff, and strong carbon crank spider optimizes your power transfer. - Stiff and lightweight. - For use with S-Works carbon road cranks.

- Universal bottom bracket style mount - 44T maximum chainring size - Impact-resistant plastic - Size: Universal - Application: BB Mount

The absoluteBLACK premium crank bolt and bolt cover sets are designed to cover the small step down between chainring and crank arms. - Designed to fit Shimano Ultegra 8000 cranks - Includes 4 T30 Torx bolts and 4 bolt covers - Not compatible with absoluteBLACK Sub Compact oval chainrings

The Taco Bashguard is designed to protect your chainring from obstacles like logs or rocks. It is hidden behind the crank and mounted to ISCG05 tabs that are located around your bottom bracket. It offers great protection for both oval and round chainrings, especially direct mount rings that cannot mount to a standard 4-bolt bashring. The Taco Bashguard fits up to a 32T oval chainring or 34T round one. - The Taco Bashguard can be used with any chainring from 26T-32T oval or 26T-34T round - Box includes taco bashguard (assembled), 6 x 1mm spacers, 3 x 3mm spacers, 3x 16mm stainless bolts, and 1 x 12mm stainless bolt - Weight: 56g

Race Face CINCH Crank Puller • Puller cap for Cinch model Race Face cranks only, including Next SL, SixC and Turbine • Puller cap utilizes 16mm hex key • 26mm thread

Race Face 15mm crank bolt/puller for 2008 and newer Evolve and Ride cranksets.

- Replacement bolt kits for mounting chain guides to ISCG and ISCG-05 frame tabs - Kits include chainline adjustment spacers - 8/12mm button head bolts for single ring steel backplate guide applications - 10/16mm flat head bolts for single ring alloy backplate guide applications

- SO-2995: hex-type steel crank fixing bolt set with integrated plastic dust cap

SRAM’s cranks are strong and tough, ready for any kind of ride. So it’s inevitable that pedal strikes and debris will chip away at the end of the crank. SRAM’s Carbon Crank Boot is an upgrade that combats the wear and tear that comes with hard riding. The boot protects the crank from surface damage and keeps the rider’s style perfectly in tact. - Injection molded plastic crank arm protection - Perfect way to protect your carbon crank investment from scratches and dents from pedal strikes - Material: Injection molded plastic - Recommended Group: XX1, X01, XX, X0

- Lower slider replacement parts for E-13 chainguides

Wheels Manufacturing Press Fit 30 Bottom Bracket Adapter for 22/24mm Spindle Cranks adapts 22/24mm Spindle Cranks (SRAM/TruVativ) to work on PF30 frames. Simply tap the adapters into the 6806 bearing in the BB shell, then install the spindle and cranks. Use Wheels Mfg Crank Spindle Spacers to adjust your chainline, or take up any side-to-side movement in your cranks. These spacers are machined from engineering-grade Delrin. Notes: - PF30-SRAM was originally designed for use with SRAM PF30 bottom brackets and will not work with Wheels Manufacturing PF30-BB, PF30-BB-AC or PF30-BB-CER. Use Wheels Mfg BBUNIV-SRAM to adapt 22/24mm Spindle Cranks (SRAM/TruVativ) in Wheels Manufacturing PF30 bottom brackets. - Not compatible with SRAM PF30 bottom brackets that use a thin plastic reducer inserted into the bearings. - The stock bottom bracket seals must be removed before installing the Pressfit 30 adapter

The Wheels Manufacturing PressFit 30 Bottom Bracket Adaptor for Shimano Cranks adapts 24mm Spindle Cranks (Shimano Hollowtech II, FSA, Race Face EXI, etc.) to work on PF30 frames. Simply tap the adapters into the 6806 bearing in the BB shell, then install the spindle and cranks. Use Wheels Mfg Crank Spindle Spacers to adjust your chainline, or take up any side-to-side movement in your cranks. These spacers are machined from engineering-grade Delrin. Notes: - PF30-SHIM was originally designed for use with SRAM PF30 bottom brackets and will not work with Wheels Manufacturing PF30-BB, PF30-BB-AC or PF30-BB-CER. Use Wheels Mfg BBUNIV-SHIM to adapt 24mm Spindle Cranks (Shimano, FSA, etc.) in Wheels Manufacturing PF30 bottom brackets. - Not compatible with SRAM PF30 bottom brackets that use a thin plastic reducer inserted into the bearings. - The stock bottom bracket seals must be removed before installing the Pressfit 30 adapter

Wheels Manufacturing BBRIGHT BB30A and PF30A Adaptor for 24mm Spindle Cranks adapts 24mm spindle cranks (Shimano, FSA, etc.) to most BBRight frames. Compatible with 2011-2012 Cervelo models R3, R3 Team, S5, S5 Team, S5 VWD, R5ca and R5 VWD. - Also adapts Cannondale BB30a and PF30a frames to 24mm spindle cranks (Shimano, FSA, etc.). - Includes eight 0.7mm shims for fine-tuning chain line - Machined engineering-grade Delrin - 48g/pr