Lighting

Compatible with Shiner and Shiner Back lights - Rubber pad with loop straps to quickly mount and remove light for recharging - 50mm bolt spacing to fit most rear racks

Mounts a Specialized Stix light to a CPSC, DIN standard reflector/rack bracket or the Specialized Pizza Rack. - Vertical CPSC hole pattern. - This mount can attach to the Horizontal Din hole pattern. - Specialized single hole pattern for the Pizza Rack. - Mounts Stix light horizontally. - Includes all mounting hardware.

The Portland Design Works Stayputnik tail light bracket has a UV-proof rubber strap to securely hold your tail light on nearly any size seat post. - Mounts in seconds and is compatible with every Portland Design Works tail light except Asteroid and Fenderbot. - UV proof rubber strap - Compatible with every PDW tail light except Asteroid and Fenderbot

Grab a set of Portland Design Works tail light brackets to mount your lights on seat posts and seat stays. - Seat post and seat stay brackets - Rubber shims included for a custom fit - Compatible with all PDW tail lights except Asteroid and Fenderbot

Mount your tail light to the reflector tab on the back of a rear cargo rack with this Rack Bracket from Portland Design Works. - Compatible with all PDW rear lights except the Asteroid and Fenderbot - Horizontal holes are 50mm apart to fit European rack standards - Vertical holes are 18mm apart to fit most reflector mounts

- Compatible with Blinky 3,5,7, Superflashes, Turbo, Turbo Minis Superflash Micros and Blinky Safety rear light - Designed specifically for aero seat posts - Adjustable light angle - Easy on/easy off design makes for quick mounting and removal

- Compatible with seatpost diameter 20mm-36mm - Adjustable light angle - Easy on/easy off design makes for quick mounting and removal - Compatible with Blinky 3,5,7, Superflashes, Turbo, Turbo Minis, Superflash Micros and Blinky Safety rear light

Others out on the roads and paths will see you when Sunlite's TL-L340 Taillight is on your bike. It sports 3 bright LEDs, steady and flashing modes, and a long run time.

- Simplistic safety light designed to be seen - Easy to install silicone strap attachment is compatible with 22.2-31.8mm bars - 3 modes including 1 steady and 2 flashing modes - Powered by 2 CR2032 batteries - Lumens: 12

- Simplistic safety light designed to be seen - Easy to install silicone strap attachment is compatible with 22.2-31.8mm bars - 3 modes including 1 steady and 2 flashing modes - Powered by 2 CR2032 batteries - Lumens: 6

The NiteRider Tail Light Strap Mount allows for quick installation and fitment on to standard seat posts. It features a quick release tab that allows you to remove just your tail light, leaving the strap mount installed on the seat post; ideal for when you leave your bike unattended or when it's time for a recharge. System Compatibility - Sentinel - Solas - Sabre - CherryBomb - TL 5.0 SL Not compatible with omega 300 and sentry aero 260 tail lights.

-Mounts easily to front racks with threaded M5 mounts -Allows for unobstructed light positioning -22.2mm clamping diameter

Put it on your seatpost, put it on your seatstay, put it anywhere—Sunlite's Griplite goes everywhere. This powerful little light boasts two LEDs and runs for a whopping 100 hours! It has steady and two flashing modes, and is housed in a water-resistant body.

Put it on your handlebars, put it on your fork leg, put it anywhere—Sunlite's Griplite goes everywhere! This powerful little light has 2 LEDs and runs for a whopping 100 hours! It has steady and flashing modes and is housed in a water-resistant body.

• 2 bright Nichia LEDs • Uses 2 CR 2032 lithium batteries (included) • 100 hour run time • 3 modes: 2 flashing and 1 steady • Water-resistant silicone body

Lezyne's Composite Bar Mount is a hard mount made of a reinforced Composite Matrix cradle for a strong and secure attachment of the Mega Drive, Deca Drive, and XL LED lights to the handlebar. It is designed for 25.4 mm or 31.8 mm bars, with the cradle designed to pivot 15 degrees laterally to allow adjustment of the LED light beam angle and directing it where it is most needed. A large thumb screw secures the CM mount to the bar without need of tools, and can be tightened by hand or a 1mm hex key. Molded rubber shims add grip and fine-tune fitting to undersized bars. Composite Bar Mounts are sold in a kit with the Mega Drive, Deca Drive, or XL LED lights.

Sunlite's HL-K100 Headlight is a great light at a great price. It sports a super-bright Krypton bulb housed in a tough, water-resistant body so it's perfect for commuting year round. A no-tools-required quick-release handlebar mount is included, too.

• 2 bright Red LEDs • Includes 2 (CR 2032) lithium batteries • 100 hour run time • 3 mode (2 flashing modes & steady mode) • Water resistant silicone body

Optional Accessory Saddle Rail Mount Bracket for most CatEye taillights.

- 1 super bright LED - Easy On/Off - Weather-tough water resistant design - Universal rubber bracket

- 1 super bright LED - Easy On/Off - Never worry waterproof design - Universal rubber bracket

- Be safe and be seen with hi-viz red LED safety lights - 360-degree visibility with rapid blink, slow blink, and full glow LED modes - Sweat-proof, water resistant design moves with you - Lightweight material for ultimate comfort - Dimensions: 2.68cm x 3.03cm x 1.02cm

Giant's Numen TL1 5 LED Taillight boasts 5 bright LEDs so you get noticed out on the road. If that wasn't enough, you have 4 modes: steady, flashing, patrol, and random modes for high visibility in traffic. And it runs for up to 180 hours. This great water-resistant light also sports 2 mounting options.

Set up a light wherever you can connect a GoPro mount. Use this adapter to connect your Imjin or Nip to any GoPro mounting option.

Mount the Nip light to an e-Bike that has the specialty Pro Max stem for accessories.

Setup a light wherever you can connect a GoPro mount. Use this adapter to connect your Taz to any GoPro mounting option.

Replacement seat post mount for the Tuck e-Bike Taillight. Secure design with non-slip strap ensures light is stationary even in rough, bumpy terrain. - Includes plastic wedge spacers to ensure Tuck mounts at optimum angle for premium visibility

Setup your Light & Motion Urban or Deckhand light (sold separately) wherever you can connect a GoPro mount. Use this adapter to connect your Urban or Deckhand to any GoPro mounting option.

Light & Motion's Vis 180 Aero Post Pad lets you easily attach your Vis 180 taillight to the back of your aero seatpost so you can be fast and visible.

This mount is designed to securely attach your Light and Motion Vis 180 Micro taillight to your bicycle.